Monday 21/10/2019

Bookmark and Share
 
 
Daily News
  PandCT RSS Daily News feed
Millers Oils explains: Hydraulic oil oxidation

8 October 2019

Oxidation, or the chemical union of oil and oxygen, is one of the primary causes of decreasing the stability of hydraulic fluids. Here Millers Oils – one of the UK’s leading oil blenders - explains what oil oxidation means, how to spot it and highlights some preventative measures that will help reduce the impact of oxidation should it occur.

What is oxidation in oil?

Oxidation is the chemical reaction with oxygen, which permanently changes the molecular structure and therefore the properties of the oil. Depending on the extent of oxidation, the oil molecules become replaced by other chemicals such as alcohols, aldehydes, ketones and acids which lead to an increase in oil viscosity, as well as deposit formation, varnishing and sludge.

What’s the best way to stop oil oxidising?

The bad news is that oxidation of hydraulic oil is unavoidable. The good news is that it can be slowed and managed by selecting the right oil and implementing oil maintenance regimes. The rate of oxidation can be accelerated by factors such as high temperature, and the presence of acids, water and wear metals e.g. copper, or slowed by the use of anti-oxidants and inherently stable base oils. By taking regular oil samples, the presence of any contaminants can be identified and remedial action such as filtration can be taken.

Millmax Longlife hydraulic oil is specially formulated to resist oxidation, using a blend of base oils with naturally high oxidation resistance coupled with the latest additive technology, to give longer service life and extended drain intervals.

What impact does oxidation have on hydraulic systems?

Oxidation reactions reduce the amount of functional oil in the system and replace it with chemicals such as acids which promote corrosion and loss in foam control, and cause an increase in viscosity, as well as deposit, varnish and sludge formation. In turn, these restrict oil flow by clogging filters, strainers and valves. Varnish build up can act as an insulating film, increasing operating temperatures and accelerating the rate of oxidation, while deposits cause wear in the system. The ultimate result of oxidation is system breakdown – most often caused by pump failure.

How can you tell if an oil has oxidised?

Two perceptible indications of hydraulic oil oxidation include foul odours and darkening of colour, as well as the more obvious presence of sludge and varnish. There are also a number of ways to determine the level of oxidation by sample analysis in the lab:

• Total Acid Number (TAN): Fresh hydraulic oil should have a TAN of around 0.2 mg KOH/g, however, this will increase as acids are produced in oxidation reactions. Once the oil has a value of 1 mg KOH/g greater than the initial value, an oil change is strongly recommended.
• Viscosity: Oxidation causes an increase in oil viscosity, as the acid molecules produced in the reactions associate, increasing the median density and therefore viscosity.
• IR spectroscopy: Oxidation products such as alcohols, aldehydes, ketones and acids can be identified in the oil by using infrared spectroscopy. A greater presence of these molecules indicates a higher level of oxidation.

Find out more

To find out more about Millers Oils’ extensive offering please visit
www.millersoils.co.uk or call 01484 713201. Millers Oils offers a sampling service to keep maintenance departments informed of the condition of their oil and equipment, so maintenance can be planned around operations, saving both time and money. To find out more about this service please visit www.millersoils.co.uk/services/oil-analysis
PandCT.com are not responsible for the content of submitted or externally produced articles and images.
Click here to email PandCT about any errors or omissions contained within this article.
     
Send this page
To send this page to a colleague or friend,
fill in the email addresses below...
Your email address
Their email address:
Page to be sent: shownews.asp?ID=54458

Company gateway pages
for Millers Oils Ltd:
FREE Information on the products in this article
To request more information,
fill in your email address below.
Your email address
 
     
Bookmark and Share
Product categories: Accelerometers | Actuators | Agitators | Analysers | Bearings | Compressors | Controllers | Conveyors | Drives | Enclosures | Flowmeters | Heat Exchangers | Motors | Pumps | Relays | Sensors | Transducers | Transmitters | Valves | Weighing
(c) Copyright 1999-2019 Process and Control Today Ltd  |  Reg. no 3733110  |  Email Editor  |  Email Webmaster  |  Sitemap  |  Privacy Policy